A spiral down cut has blades which forces chips down back into your material. This has benefits of providing a perfect top finish to any wood type especially plys and top finishes. Made of a very high tungsten carbide material, down cut bits are the a weapon of choice in anyone's arsenal. Opposite to a spiral up cut, a down cut will give you a perfect top finish but a burred bottom finish if cutting all the way through. These bits therefore are most effective for engraving & lettering rather than cutting all the way through.
Suitable for
- Wood (MDF, hardwood, ply & softwoods)
Adam’s Tips
Just like a straight flute, a down cut creates a lot of dust as opposed to chips so make sure you have appropriate ventilation or dust extraction when cutting. On the plus side, the dust gets stuck and packed back into the slot you have made and keeps your cut item in place. This has the advantage of not having to use tabs or tape to hold your material down although can add time back in with the need to deburr the bottom edge.
| Feeds and Speeds - 2 Flute Down Cut mm per minute |
|||
| Wood | |||
| Item Code | Description | Soft | Hard |
| 1-1/8-DC-2F-4 | 1mm x 3.175mm x 4mm 2F | 1,300 | 650 |
| 1.5-1/8-DC-2F-6 | 1.5mm x 3.175mm x 6mm 2F | 2,000 | 1,000 |
| 2-1/8-DC-2F-8 | 2mm x 3.175mm x 8mm 2F | 2,750 | 1,400 |
| 1/8-1/8-DC-2F-17 | 3.175mm x 3.175mm x 17mm 2F | 3,900 | 1,950 |
| 1/8-1/8-DC-2F-22 | 3.175mm x 3.175mm x 22mm 2F | 3,100 | 1,550 |
| 4-4-DC-2F-22 | 4mm x 4mm x 22mm 2F | 4,800 | 2,400 |
| 6-6-DC-2F-22 | 6mm x 6mm x 22mm 2F | 11,950 | 6,000 |
| 3.175-6.35-DC-2F-17 | 3.175mm x 6.35mm x 17mm 2F | 3,900 | 1,950 |
| 4-6.35-DC-2F-22 | 4mm x 6.35mm x 22mm 2F | 4,800 | 2,400 |
| 6.35-6.35-DC-2F-22 | 6.35mm x 6.35mm x 22mm 2F | 13,850 | 6,950 |
| 8-8-DC-2F-32 | 8mm x 8mm x 32mm 2F | 16,900 | 8,450 |
| 10-10-DC-2F-52 | 10mm x 10mm x 52mm 2F | 14,300 | 7,150 |
| Revolutions per minute 16,000RPM | |||
| 100% width per cut slotting | |||
| Depth per cut Diameter x 1 | |||
42 Reviews Hide Reviews Show Reviews
-
2 FLUTE COMPRESSION UP DOWN CARBIDE END MILL
Works fine for me
-
Love them
These are amazing quality
-
Top notch
By far the best I’ve used, sharp clean cuts which is what I need to do my inlay work on guitars.
-
Down cut end mill bit, 4 mm
We had noticed that when routing out certain timbers, especially radiata pine, the top of the cut tends to splinter and "fuzz" , necessitating laborious sanding. This bit gives a clean edge at the surface of cut-outs. The downside is that chips do tend to lay in the cut more, but not seriously, and the bottom edges of through cuts are not as clean. We next intend to try a "compression" cutter.
-
2 flute downcut bit.
Quality product, clean cutting with excellent chip removal.
-
Quality Makes a difference
This is a deep cut bit I expected to break due to the length. But, I have not. I even bought extras, just in case. This bit has been great, and would highley recommend it, and others
-
Great bit
I love the crisp top edge this leaves
-
2 flute down cut
Nice clean cut no chipout,
-
2 Flute DOWN CUT Carbide End Mill
Excellent cutting and finish. Also fast reliable service upon purchase.
