Skip to main content

4 Flute SPIRAL Carbide End Mill TiSiN HRC 55

Adam's Bits

$18.95
(20 reviews) Write a Review
SKU:
6-6-SP-4F-15-C55 [X-S8]
Suitable Material:
Steel / Stainless steel
Cutter Profile:
4 flute square
Suitable Use:
CNC
Adding to cart… The item has been added

A 4 flute spiral end mill is the general purpose cutter for steel. Four flutes give a stronger core and a finer finish than a 2 flute, at the cost of chip room, which is why it suits side (peripheral) milling and light slotting rather than deep full-width slots. The TiSiN coating lets it run in carbon steel, alloy steel, stainless and pre-hardened material up to HRC55 without the edge burning off.

On a CNC router this is the cutter for steel brackets, jigs and fixtures where you need accurate walls and a square corner. For aluminium use a 2 or 3 flute uncoated or DLC end mill instead; the extra flutes on this tool will pack up with soft, gummy chips.

4 flute solid carbide slot mill with a TiSiN coating giving it a capability to cut materials up to HRC55. This mill is primarily used for edge or peripheral milling.

Sizes run from 1mm to 16mm cutting diameter on 4mm to 16mm shanks, with standard and extra-long cut lengths in the popular sizes.

Every size lists a starting feed rate on the product page where we have tested it. For the method behind the numbers read the Feeds & Speeds Guide, or use Message Adam above if you're unsure which size suits your machine.

Stocked in our Laverton North (Melbourne) warehouse and shipped Australia-wide. Standard shipping is free on orders over $200.

Sizes and dimensions

4 Flute SPIRAL Carbide End Mill TiSiN HRC 55 comes in 17 sizes. Pick yours from the size options above; the dimensions for each are listed here.

Cutting diameterShankCut lengthSKU
1mm4mm4mm1-4-SP-4F-4-C55
1.5mm4mm4mm1.5-4-SP-4F-4-C55
2mm4mm6mm2-4-SP-4F-6-C55
3mm4mm8mm3-4-SP-4F-8-C55
4mm4mm11mm4-4-SP-4F-10-C55
4mm4mm20mm4-4-SP-4F-20-C55
5mm5mm35mm5-5-SP-4F-35-C55
6mm6mm15mm6-6-SP-4F-15-C55
6mm6mm40mm6-6-SP-4F-40-C55
8mm8mm20mm8-8-SP-4F-20-C55
8mm8mm40mm8-8-SP-4F-40-C55
10mm10mm25mm10-10-SP-4F-25-C55
10mm10mm35mm10-10-SP-4F-35-C55
10mm10mm50mm10-10-SP-4F-50-C55
12mm12mm30mm12-12-SP-4F-30-C55
14mm14mm45mm14-14-SP-4F-45-C55
16mm16mm45mm16-16-SP-4F-45-C55

20 Reviews Hide Reviews Show Reviews

  • 5
    End mill

    Posted by Kevin Handasyde on 25th Mar 2019

    Good quality tool has good life span

  • 5
    HRC 55 4F end mill

    Posted by Michael Kemp on 6th Jun 2018

    I have purchased a few of these cutters and used them to machine Bohler M200 tool steel. The bits have exceeded the life expectancy as indicated on the Bohler data sheet for solid carbide cutting tools on this material. I'm happy with them, and very happy with the service from Adam.