Skip to main content

2 Flute V Bit Carbide End Mill (for Engraving)

Adam's Bits

$26.84
(54 reviews) Write a Review
SKU:
0.1-6-V-2F-30 [X-D3]
Suitable Material:
Wood
Cutter Profile:
2 flute V bit
Suitable Use:
CNC
Adding to cart… The item has been added

A 2 flute V bit carbide end mill is an engraving and V-groove tool that pairs a sharp V-point with two cutting edges, giving you a clean, fast, precise cut for detailed work. It’s ideal for engraving, lettering, sign making and V-carving, as well as chamfering and bevelling edges. The two flutes share the cutting load for a smooth finish and let you run higher feed rates than a single flute, while the solid carbide construction holds a keen point for crisp, sharp detail straight off the machine.

Like all V-bits, the groove width is set by how deep you cut — the deeper the pass, the wider the line — which is exactly what V-carving software relies on, varying the depth to swell and taper strokes and to sharpen internal corners. The result is fine, controlled detail across a wide range of materials, from decorative lettering and inlays to clean chamfers and edge profiles.

Suitable for

  • Hardwood and softwood, plywood and MDF
  • Engraving, lettering, sign making and V-carve work
  • Chamfers, bevels, inlays and decorative edge detailing

Not ideal for

  • Soft, gummy materials — plastics and foam can pack the flutes; a single-flute V-bit clears chips and runs cooler in those
  • Deep grooving — a V-profile widens as it goes deeper, so it’s made for engraving and decorative lines, not deep slots
  • Flat-bottomed pockets — use a straight or end mill where you need a square base rather than a V

Adam’s Tips

Let your CAM software drive the Z depth for V-carving rather than setting a fixed depth of cut — because depth controls line width, the design should dictate how deep each stroke goes. Always run a quick test on scrap in the same material to confirm your point depth and line width before committing to the finished piece; a small depth change makes a visible difference to lettering.

Use the two flutes to your advantage. With the cutting load shared across two edges, you can lift the feed rate compared with a single-flute V-bit and still hold a clean edge. If you’re getting a rough or burnt line, it’s usually feeding too slowly for the RPM — speed the feed up rather than backing it off.

Protect the tip — the fine point is the working part of the tool and the first thing to chip. Ease into the cut, keep your plunge moves gentle, and store the bit so the point is protected. In harder or resinous timber, clear the cut and wipe any build-up off the bit to keep it engraving sharp and clean.

Sizes and dimensions

2 Flute V Bit Carbide End Mill (for Engraving) comes in 20 sizes. Pick yours from the size options above; the dimensions for each are listed here.

AngleTip widthShankSKU
20°0.1mm3.175mm (1/8")0.1-3.175-V-2F-20
20°0.1mm6mm0.1-6-V-2F-20
20°0.3mm3.175mm (1/8")0.3-3.175-V-2F-20
20°0.3mm6mm0.3-6-V-2F-20
30°0.1mm3.175mm (1/8")0.1-3.175-V-2F-30
30°0.1mm6mm0.1-6-V-2F-30
30°0.3mm3.175mm (1/8")0.3-3.175-V-2F-30
30°0.3mm6mm0.3-6-V-2F-30
45°0.1mm3.175mm (1/8")0.1-3.175-V-2F-45
45°0.1mm6mm0.1-6-V-2F-45
45°0.3mm3.175mm (1/8")0.3-3.175-V-2F-45
45°0.3mm6mm0.3-6-V-2F-45
60°0.1mm3.175mm (1/8")0.1-3.175-V-2F-60
60°0.1mm6mm0.1-6-V-2F-60
60°0.3mm3.175mm (1/8")0.3-3.175-V-2F-60
60°0.3mm6mm0.3-6-V-2F-60
90°0.1mm3.175mm (1/8")0.1-3.175-V-2F-90
90°0.1mm6mm0.1-6-V-2F-90
90°0.3mm3.175mm (1/8")0.3-3.175-V-2F-90
90°0.3mm6mm0.3-6-V-2F-90

Frequently asked questions

What is a 2 flute V bit best for?

V-carving, lettering, signs and chamfers where a crisp point matters. The two cutting edges share the load for a smoother line and faster feeds than a single flute.

Which angle should I choose?

Angles run from 20° to 90°. Smaller angles cut deeper, narrower detail; 60° and 90° are the usual choices for signs and chamfers. The groove width depends on how deep you cut.

Can I use it on plastics or foam?

Not on HDPE or EVA foam. For soft plastics and foam, use the 1 flute V bit.

Which shank size do I need?

It comes on 3.175mm (1/8") and 6mm shanks. Match the shank to your collet.

54 Reviews Hide Reviews Show Reviews

  • 5
    High quality

    Posted by Norman Waugh on 12th Apr 2024

    Great service by Adam. Easy to order and prompt delivery.

  • 5
    v bit

    Posted by Lynn Palmer on 26th Mar 2024

    Perfect for my miniatures

  • 5
    Exceeded my expectations

    Posted by Cam H on 7th Nov 2023

    Wow! I can't believe i used to waste money on those cheap eBay single flute engraving bits, not only do these leave a nicer finish, but they last A LOT longer. 10/10

  • 5
    2 flute V bit

    Posted by Greg Hodson on 18th Sep 2023

    Once again, prompt delivery and excellent service. This bit is easy to use, even with my full size router. Everything I do is hand routed and I am pleased with the quality of this bit. Thanks again

  • 5
    Engraving 2 Flute V Bit Solid Carbide

    Posted by Kerry Hinge on 6th Aug 2023

    This worked perfectly for a brass engraving job I had to do with a 3018 CNC machine.

  • 5
    2 FLUTE V BIT CARBIDE END MILL (FOR ENGRAVING)

    Posted by Dave Horan on 30th Jun 2023

    great bit great service as always

  • 5
    Awesome

    Posted by Greg on 25th Jun 2023

    Great bit and long lasting. Very very happy.

  • 5
    GR8

    Posted by COLIN NEWALL on 19th May 2023

    GR8

  • 5
    V groove bit

    Posted by Jason Roberts on 8th May 2023

    While I am just starting out using my bluey cnc, I am having fun using it. I recently bought the v groove 2 flute bit and it work’s fantastic and I have tried it on just about everything from soft to hard wood and resin and it doesn’t miss a beat, highly recommend