Skip to main content

DLC vs Uncoated vs TiSiN: Which End Mill Coating Do You Need?

Posted by Adam M. on 5th Nov 2026

Most of our solid carbide bits come in more than one coating, and the coating matters as much as the flute count. Match the coating to the material, because a coating that helps in steel can hurt in aluminium. Here's how DLC, uncoated, TiSiN and our XB wood coating compare, and when each is worth paying for.

Uncoated carbide: sharpest edge

Uncoated carbide can be ground to the keenest edge, which keeps cutting forces and heat low in soft materials. It's the standard for wood, MDF, plastics and foam, and a good budget choice for aluminium and brass. Its weakness is that soft, gummy chips such as aluminium can stick to the bare carbide and build up on the edge.

Examples: up cut, 1 flute for plastics and the HRC45 ball nose for non-ferrous metals.

DLC (diamond-like carbon): the aluminium coating

DLC is extremely hard and extremely slippery. Aluminium chips slide off the flute instead of welding to it, the edge stays sharp far longer than bare carbide, and you can push the feed up without the finish falling away. Our 3 flute DLC cutters are rated for up to 100% more tool life than uncoated and can be run dry. DLC cutters also run quieter and leave a brighter, near-mirror finish.

Use it for aluminium, brass, copper and other non-ferrous metals, ACM and, as a compression cutter, panel products where resin build-up shortens edge life. The range includes the 1 flute, 2 flute and 3 flute up cuts, the DLC ball nose and the DLC compression.

Don't use it for steel or stainless. DLC isn't designed for the heat of ferrous cutting.

TiSiN: steel and hard materials

TiSiN adds heat resistance and surface hardness, so the edge holds up at the temperatures steel generates. Our TiSiN end mills, ball noses and chamfer mills are rated for steel, stainless and cast iron up to HRC55. In aluminium, TiSiN gives no benefit over DLC or uncoated, and the slightly rounder coated edge can make chips stick, so keep it for ferrous work.

Examples: TiSiN ball nose, 90° chamfer mill and corner rounding mill.

XB coating: production wood and panel

Our industrial XB range is European carbide with an Australian-exclusive coating rated for up to 200% the life of uncoated bits. It's built for production nesting of ply, MDF, melamine and laminate on flatbed CNCs that can run the feed rates these cutters need. See the XB compression and XB 3 flute rougher.

Quick guide

MaterialBest choice
Wood, MDF, ply (hobby)Uncoated
Ply, MDF, melamine (production)XB, or DLC compression
Plastics and acrylicUncoated single flute
Aluminium, brass, copperDLC (uncoated on a budget)
Steel, stainless, cast ironTiSiN

Adam's Tip

If you cut aluminium more than occasionally, DLC pays for itself. The edge stays clean, so you'll stop fighting built-up edge and re-cut chips. Keep using air or mist to clear the chips either way: coating helps chips slide off, but it can't stop them being cut twice.

Frequently asked questions

Is DLC better than uncoated for aluminium?

Yes, for most aluminium work. DLC resists chip welding, stays sharp longer (up to 100% more life on our 3 flute DLC) and leaves a brighter finish. Uncoated is still a good budget option.

Can I use a DLC end mill on steel?

No. Use a TiSiN-coated end mill for steel, stainless and cast iron. DLC is for aluminium and other non-ferrous metals.

Do I need coated bits for wood?

Not for hobby work. Uncoated carbide is the standard for timber and MDF. Coated XB or DLC compression cutters pay off in production nesting, where edge life and resin build-up matter.

What coating is best for plastics?

Uncoated carbide with a single polished flute. The sharp edge and big chip carry the heat away before the plastic can melt.