Skip to main content

1 Flute UP CUT Carbide End Mill (for Plastics)

Adam's Bits

$3.59
(84 reviews) Write a Review
SKU:
1/8-1/8-SP-1F-17 [B6]
Suitable Material:
Wood / Plastics / Foam
Cutter Profile:
1 flute up cut
Suitable Use:
CNC
Adding to cart… The item has been added

A 1 flute up cut carbide end mill is purpose-built for cutting plastics cleanly and cool. It runs a single cutting edge with a large, open flute, and the up-cut spiral pulls chips up and out of the cut as it works. That aggressive chip evacuation is exactly what plastics need — it keeps the cutting zone clear, stops chips from being re-cut, and carries heat away before it can melt or re-weld the material. The result is a smooth, gummy-free finish in materials that would quickly melt or pack up behind a multi-flute bit.

The single flute is the key. With only one edge, each revolution takes a bigger, cleaner chip and leaves far more room to clear it — so the bit can run fast without generating the friction heat that melts acrylic and polycarbonate. Because the up-cut geometry lifts chips upward, it leaves the cleanest edge on the bottom face of the workpiece and clears deep slots without packing. The trade-off is the mirror image of a down-cut bit: chips exit on top, so it needs good hold-down and can leave a rougher top edge on thin or delicate stock.

Suitable for

  • Acrylic (cast and extruded / PMMA) and polycarbonate (Lexan)
  • ABS, HDPE, nylon, acetal (Delrin), PVC and most machinable plastics
  • Foams, and soft timbers where fast chip clearance matters

Not ideal for

  • Plys— the up-cut can fray or chip the top surface; use a down-cut bit instead
  • Thin, unsupported sheet without solid hold-down — the upward pull can lift or chatter the material
  • Hard metals and steel — this tool is optimised for plastics and soft materials, not ferrous cutting

Adam’s Tips

The most common problem cutting plastic is melting, and the fix is almost always counter-intuitive: if the edge is gummy or the chips are re-welding, increase your feed rate or drop your RPM. A single flute relies on a decent chip load — a bigger chip carries the heat out of the cut with it, while a slow feed just rubs and melts. Aim to keep the chips flowing and clearing, not powdering.

Because an up-cut bit pulls chips (and the material) upward, good work holding is essential — use a vacuum table, clamps, or tape-and-glue on thin sheet to stop it lifting. 

Feeds and Speeds - 1 Flute for Plastics
mm per minute
   
 Plastics/Wood 
Item Code Description  Soft   Hard 
0.8-3.175-SP-1F-3 0.8mm x 3.175mm x 3mm  1F 650 350
1-3.175-SP-1F-4 1mm x 3.175mm x 4mm  1F 800 400
1.5-1/8-SP-1F-6 1.5mm x 3.175mm x 6mm  1F 1,250 650
2-1/8-SP-1F-8 2mm x 3.175mm x 8mm  1F 1,700 850
2-1/8-SP-1F-12 2mm x 3.175mm x 12mm  1F 1,450 750
2.5-1/8-SP-1F-12 2.5mm x 3.175mm x 12mm  1F 2,050 1,050
1/8-1/8-SP-1F-12 3.175mm x 3.175mm x 12mm  1F 3,050 1,550
1/8-1/8-SP-1F-17 3.175mm x 3.175mm x 17mm  1F 2,450 1,250
1/8-1/8-SP-1F-22 3.175mm x 3.175mm x 22mm  1F 1,950 1,000
4-4-SP-1F-17 4mm x 4mm x 17mm  1F 3,800 1,900
4-4-SP-1F-22 4mm x 4mm x 22mm  1F 3,000 1,500
6-6-SP-1F-17 6mm x 6mm x 17mm  1F 9,350 4,700
6-6-SP-1F-22 6mm x 6mm x 22mm  1F 7,500 3,750
6-6-SP-1F-32 6mm x 6mm x 32mm  1F 4,800 2,400
6-6-SP-1F-52 6mm x 6mm x 52mm  1F 1,950 1,000
3.175-6.35-SP-1F-17 3.175mm x 6.35mm x 17mm  1F 2,450 1,250
4-6.35-SP-1F-22 4mm x 6.35mm x 22mm  1F 3,000 1,500
6.35-6.35-SP-1F-22 6.35mm x 6.35mm x 22mm  1F 8,650 4,350
8-8-SP-1F-22 8mm x 8mm x 22mm  1F 16,550 8,300
10-10-SP-1F-22 10mm x 10mm x 22mm  1F 34,300 17,150
12-12-SP-1F-32 12mm x 12mm x 32mm  1F 43,650 21,850
       
Revolutions per minute 16,000RPM    
100% width per cut slotting    
Depth per cut Diameter x 1    

Sizes and dimensions

1 Flute UP CUT Carbide End Mill (for Plastics) comes in 43 sizes. Pick yours from the size options above; the dimensions for each are listed here.

Cutting diameterShankCut lengthSKU
0.8mm (1/32")3.175mm (1/8")3mm0.8-3.175-SP-1F-3
1mm3.175mm (1/8")4mm1-3.175-SP-1F-4
1.5mm3.175mm (1/8")6mm1.5-1/8-SP-1F-6
2mm3.175mm (1/8")8mm2-1/8-SP-1F-8
2mm3.175mm (1/8")12mm2-1/8-SP-1F-12
2.5mm3.175mm (1/8")8mm2.5-1/8-SP-1F-8
2.5mm3.175mm (1/8")12mm2.5-1/8-SP-1F-12
3.175mm (1/8")3.175mm (1/8")8mm1/8-1/8-SP-1F-8
3.175mm (1/8")3.175mm (1/8")12mm1/8-1/8-SP-1F-12
3.175mm (1/8")3.175mm (1/8")17mm1/8-1/8-SP-1F-17
3.175mm (1/8")3.175mm (1/8")22mm1/8-1/8-SP-1F-22
3.175mm (1/8")3.175mm (1/8")32mm1/8-1/8-SP-1F-32
3.175mm (1/8")6mm17mm3.175-6-SP-1F-17
3.175mm (1/8")6.35mm (1/4")17mm3.175-6.35-SP-1F-17
4mm4mm12mm4-4-SP-1F-12
4mm4mm17mm4-4-SP-1F-17
4mm4mm22mm4-4-SP-1F-22
4mm4mm32mm4-4-SP-1F-32
4mm4mm42mm4-4-SP-1F-42
4mm6mm17mm4-6-SP-1F-17
4mm6.35mm (1/4")22mm4-6.35-SP-1F-22
4.67mm6mm17mm4.67-6-SP-1F-17
5mm6mm17mm5-6-SP-1F-17
5mm6mm22mm5-6-SP-1F-22
5mm6mm32mm5-6-SP-1F-32
6mm6mm12mm6-6-SP-1F-12
6mm6mm17mm6-6-SP-1F-17
6mm6mm22mm6-6-SP-1F-22
6mm6mm32mm6-6-SP-1F-32
6mm6mm42mm6-6-SP-1F-42
6mm6mm52mm6-6-SP-1F-52
6.35mm (1/4")6.35mm (1/4")22mm6.35-6.35-SP-1F-22
6.35mm (1/4")6.35mm (1/4")32mm6.35-6.35-SP-1F-32
6.35mm (1/4")6.35mm (1/4")42mm6.35-6.35-SP-1F-42
8mm8mm22mm8-8-SP-1F-22
8mm8mm32mm8-8-SP-1F-32
8mm8mm42mm8-8-SP-1F-42
8mm8mm52mm8-8-SP-1F-52
10mm10mm22mm10-10-SP-1F-22
10mm10mm32mm10-10-SP-1F-32
10mm10mm52mm10-10-SP-1F-52
12mm12mm32mm12-12-SP-1F-32
12mm12mm52mm12-12-SP-1F-52

Frequently asked questions

Why use a 1 flute bit for plastics?

The single large polished flute lifts chips out fast, so heat leaves with the chip instead of melting the plastic. Multi-flute bits re-cut chips and can weld acrylic back into the slot.

Which plastics can it cut?

Acrylic, polycarbonate, ABS, HDPE, nylon, acetal and PVC. It also works well in softwood and XPS foam.

Does it work on plywood or steel?

It is not recommended for plywood or steel. For aluminium and hard plastics, the 1 Flute Up Cut DLC is the better choice.

Why are my thin sheets lifting?

An up cut pulls material upward. Use solid hold-down such as double-sided tape, masking tape and super glue, or clamps, and tabs on small parts.

What speed should I run?

16,000 rpm is a good start. Set the feed with the calculator at feeds.endmill.com.au.

84 Reviews Hide Reviews Show Reviews

  • 5
    Great milling bit

    Posted by Mick Gulovsen on 17th Nov 2026

    I have been having trouble with cutting soft plastics and getting build up on the tip. These bits work beautifully and no buildup on the tip.

  • 5
    Very happy with my selection of uncut bits

    Posted by Anthony on 4th Nov 2026

    It done everything I needed to on my CNC machine and good finish

  • 3
    Single Flute Upcut

    Posted by Chris on 1st Sep 2026

    Been using these cutters for while now very happy with them

  • 5
    3mm EM

    Posted by P&M Plastics on 14th Aug 2026

    Great cutters, great results using them with HDPE and Polycarb

  • 5
    1 flute upcut bit

    Posted by Andrew on 13th Jul 2026

    Good quality bits delivered quickly. I will continue to buy from Adam's Bits.

  • 5
    1 flute up cut carbide end mill for plastics.

    Posted by James Bravington on 6th Jul 2026

    The end mill is sharp, its dimensions are as described and it is robust. I have used it several times and have gotten excellent results and so far no loss of sharpness.

  • 5
    Up cut end mill for plastics

    Posted by Robert on 16th Jun 2026

    Worked very well with a clean cut.

  • 5
    Sigle Flute carbide up cutter for plastics

    Posted by Daniel on 7th Jan 2026

    This is a great cutter, we can run higher feed-rates than our previous tools and the cutters are much less expensive. Highly recommended.

  • 5
    Single flute upcut Endmill

    Posted by Kieran on 3rd Nov 2025

    Great cutters, work well with hard and soft plastics